Shop for spiral end mill shank solid carbide

This set includes 3 superior quality spiral up cut Router bits made from premium solid micro-grain carbide. for use on soft and hard woods, ply-woods, composites, laminates, plastics and some non-ferrous metals. Ideal for grooving, dado cuts and mortise and tenon joints. Can also be used for slotting. Bit 1: Shank-1/4 in. Cutting Diameter:1/4 in. Cutter Height: 1 in. Overall Height: 2-1/2 in. Bit 2: Shank: 1/2 in. Cutting Diameter: 3/8 in. Cutter Height: 1-1/8 in. Overall Height: 3 in. Bit 3: Shank: 1/2 in. Cutting Diameter: 1/2 in. Cutter Height: 1-3/8 in. Overall Height: 3 in. Bits produce fast, clean and accurate cuts and will stay sharper longer. Up cut spiral provides for excellent chip removal pulling chips up and away from your work towards the router. Set includes a beautiful solid wood storage case. Up cut endmills are great for all standard milling and material removal. These bits pull the wood chips up and away from the tool path which helps prevent tool breakage and extends the life of the bit. If a particular finish is required for your project, use a down cut or compression cut end mill for the final pass.

Best used for: Laminate or veneer-finish plunging and dadoing. Cutting Diameter: 1/8 in. Cutting Height: 1/2 in. Shank Diameter: 1/4 in. Overall Length: 2 in. Flutes: 2 Down cut endmills shear in a downward direction causing the uppermost layer of the material to be pressed down against the material just below it. This motion leaves a perfectly clean top surface edge. A concentration of wood chips in the work path will occur. Hose away excess wood chips to prevent bit breakage. Down cut CNC end mills are great for dado, pocket and inlay work as well as the final pass on most projects. These bits are especially useful when routing material such as melamine and plywood. Down cut spiral bits are designed to produce perfectly clean edges on the top face of the work piece but since the bits geometry causes the wood chips to travel in a downward direction, which will cause the tool path to be obstructed, it should only be used in applications where the desired finish is required.

Best used for: Standard milling, dadoing, and boring. Cutting Diameter: 1/4 in. Cutting Height: 2 in. Shank Diameter: 1/4 in. Overall Length: 4 in. Flutes: 2 Up-cut endmills direct woodchips up and away from the milling area leaving an unobstructed path for the endmill. Bit breakage is less likely. Up cut end mills are the best choice for most standard milling applications. The up cut direction can leave behind a minimally rough top surface edge. Up cut endmills are great for all standard milling and material removal. These bits pull the wood chips up and away from the tool path which helps prevent tool breakage and extends the life of the bit. If a particular finish is required for your project, use a down cut or compression cut end mill for the final pass.

This bit features a 1/4 in. cutting diameter, 1 in. cutting length and 90° V-groove tip with and overall length of 2-1/2 in. with a 1/4 in. shank. This muti-function bit is used for lettering, boring, counter sinking and milling all in one saving you time and money. Up cut endmills are great for all standard milling and material removal. These bits pull the wood chips up and away from the tool path which helps prevent tool breakage and extends the life of the bit. If a particular finish is required for your project, use a down cut or compression cut end mill for the final pass.

Best used for: Laminate or veneer-finish plunging and dadoing. Cutting Diameter: 7/32 in. Cutting Height: 1 in. Shank Diameter: 1/4 in. Overall Length: 2-1/2 in. Flutes: 3 Down cut endmills shear in a downward direction causing the uppermost layer of the material to be pressed down against the material just below it. This motion leaves a perfectly clean top surface edge. A concentration of wood chips in the work path will occur. Hose away excess wood chips to prevent bit breakage. Down cut CNC end mills are great for dado, pocket and inlay work as well as the final pass on most projects. These bits are especially useful when routing material such as melamine and plywood. Down cut spiral bits are designed to produce perfectly clean edges on the top face of the work piece but since the bit's geometry causes the wood chips to travel in a downward direction, which will cause the tool path to be obstructed, it should only be used in applications where the desired finish is required.

Best used for: Standard milling, dadoing, and boring. Cutting Diameter: 3/8 in. Cutting Height: 1-1/4 in. Shank Diameter: 3/8 in. Overall Length: 2-1/2 in. Flutes: 3 Up-cut endmills direct woodchips up and away from the milling area leaving an unobstructed path for the endmill. Bit breakage is less likely. Up cut end mills are the best choice for most standard milling applications. The up cut direction can leave behind a minimally rough top surface edge. Up cut endmills are great for all standard milling and material removal. These bits pull the wood chips up and away from the tool path which helps prevent tool breakage and extends the life of the bit. If a particular finish is required for your project, use a down cut or compression cut end mill for the final pass.

Best used for: Standard milling, dadoing and boring. Cutting Diameter: 3/16 in. Cutting Height: 3/4 in. Shank Diameter: 1/4 in. Overall Length: 2 in. Flutes: 2 Up-cut endmills direct woodchips up and away from the milling area leaving an unobstructed path for the endmill. Bit breakage is less likely. Up cut end mills are the best choice for most standard milling applications. The up cut direction can leave behind a minimally rough top surface edge. Up cut endmills are great for all standard milling and material removal. These bits pull the wood chips up and away from the tool path which helps prevent tool breakage and extends the life of the bit. If a particular finish is required for your project, use a down cut or compression cut end mill for the final pass.

Best used for: Standard milling, dadoing and boring. Cutting Diameter: 3/8 in. Cutting Height: 1 in. Shank Diameter: 3/8 in. Overall Length: 2-1/2 in. Flutes: 2 Up-cut endmills direct woodchips up and away from the milling area leaving an unobstructed path for the endmill. Bit breakage is less likely. Up cut end mills are the best choice for most standard milling applications. The up cut direction can leave behind a minimally rough top surface edge. Up cut endmills are great for all standard milling and material removal. These bits pull the wood chips up and away from the tool path which helps prevent tool breakage and extends the life of the bit. If a particular finish is required for your project, use a down cut or compression cut end mill for the final pass.

Best used for: Standard milling, dadoing and boring. Cutting Diameter: 5/16 in. Cutting Height: 1 in. Shank Diameter: 5/16 in. Overall Length: 2-1/2 in. Flutes: 2 Up-cut endmills direct woodchips up and away from the milling area leaving an unobstructed path for the endmill. Bit breakage is less likely. Up cut end mills are the best choice for most standard milling applications. The up cut direction can leave behind a minimally rough top surface edge. Up cut endmills are great for all standard milling and material removal. These bits pull the wood chips up and away from the tool path which helps prevent tool breakage and extends the life of the bit. If a particular finish is required for your project, use a down cut or compression cut end mill for the final pass.

Best used for: Standard milling, dadoing and boring. Cutting Diameter: 7/32 in. Cutting Height: 1 in. Shank Diameter: 1/4 in. Overall Length: 2-1/4 in. Flutes: 2 Up-cut endmills direct woodchips up and away from the milling area leaving an unobstructed path for the endmill. Bit breakage is less likely. Up cut end mills are the best choice for most standard milling applications. The up cut direction can leave behind a minimally rough top surface edge. Up cut endmills are great for all standard milling and material removal. These bits pull the wood chips up and away from the tool path which helps prevent tool breakage and extends the life of the bit. If a particular finish is required for your project, use a down cut or compression cut end mill for the final pass.